Buzzers meet NEMA 4X for protection and corrosion resistance in washdown environments.

Keep an eye on leaks, overflow, and temperature changes near your equipment, even when you’re offsite.

Buzzers are UL listed for use in environments where flammable gases, combustible dust, and combustible fibers may be present.

Horns are UL and C-UL listed for indoor and outdoor use in Class I, Division 2, Groups A, B, C, and D; Class II, Division 2, Groups F and G; and Class III, Division 2 hazardous locations.

When this horn runs out of air, recharge it with the included pump.

These horns have disposable canisters that can be replaced when the propellant is gone.

The built-in motor-driven fan in these sirens generates a shrill tone that's audible over long distances.

Apply air or steam pressure to produce a shrill tone and alert workers. Signal continues as long as pressure is applied.

This alarm plays a recorded message when it detects someone passing within 6 1/2 feet.

Just like the bells you hear at service stations, these bells ring when a vehicle drives over the attached hose.

A chime announces when someone passes through the infrared light beam and a counter keeps track of each entrance and exit.

Arm and disarm these alarms with a key.

Lights combine high-visibility strobes with a buzzer that warns workers of hazards even when they’re outside a direct line of sight.

The revolving motion of the light makes these more visible than flashing lights.

The pad below the base absorbs shock and vibration.

Direct your signal with these lights; they flash in one direction.

Place these lights in full sun and their batteries charge during daylight hours. Lights automatically switch on at dusk and off at dawn.

Small as hockey pucks, these lightweight strobe lights mount to surfaces and are unobtrusive when they’re turned off.

Easier to spot than other strobe lights, these lights emit bursts of multiple flashes.

Easier to spot than other strobe lights, these lights emit bursts of five flashes per cycle.

A series of four flashes per cycle makes these lights more visible than other strobe lights.

Set these portable lights wherever you need a signal light—they don't need to be wired or plugged in.

Carry these lights around with you and place them wherever needed.

Mount these lights to the top of towers to warn low-flying aircraft.

These lights are rated IP69K to withstand high-pressure washdowns, such as those in food and beverage applications.

These lights have LED bulbs for years of maintenance-free operation and can be wired as either continuous or flashing.

Use a computer to program colors, lighting patterns, and sounds to communicate a variety of status conditions, material levels, and cycle times—these stack lights have 21 colors and 11 sounds.

These lights have lenses that snap in and out, so you can easily swap colors or change their position in the stack.

Design a stack light with your choice of light pattern and color. Start with a base, then add up to five modules total—twist and lock them together.

Use these lights in tight spaces in place of a tower. They emit three colors from a single lens.

These lights emit three colors from a single lens and can be mounted in tight spaces where a tower will not fit.

When motion is detected from both directions at a two-way corner, these lights flash to alert personnel and prevent collisions.

Warn about the presence of smoke with this stand-alone detector.

When this detector senses carbon monoxide, it sends a signal to your control panel and sounds an alarm.

Check that your HVAC smoke detector is working properly. Wire these test stations to your smoke detector controller to test difficult to access smoke detectors from a convenient location.

Protect your detectors from damage and tampering.

In addition to an audible signal, these alarms flash a high-intensity strobe to draw attention during fire emergencies.

Install these stations throughout your facility for quick access in case of a fire.

Protect your fire alarm stations from damage.

Count down to zero or count up to as much as 24 hours with these digital timers.

Track time on food processing lines while reducing the risk of contaminating the food. To help you comply with Hazard Analysis and Critical Control Point (HACCP) programs, these plastic stopwatches contain metal and chemical additives that will set off metal detectors and show up on X-ray machines.

These thermometers have a thermocouple probe that can handle extreme temperatures, and come with a calibration certificate traceable to NIST that states they have passed a test for accuracy.

Determine relative humidity within ±4% accuracy and temperature within ±1.8° F accuracy. This meter comes with a calibration certificate traceable to NIST that states it has passed a test for accuracy.

Remotely record temperature, humidity, and dew point up to 10 feet from the display and set the alarm to sound and flash the display if temperature readings rise above or fall below a set range.

Monitor pressure in your system from a distance by using this display in conjunction with pressure transmitters.

Attach these timers to faucets to make sure you’re following handwashing protocols that help prevent the spread of illness.

With no moving parts as well as sealed electronic components, this horn is built to last even in wet conditions.

These alarms beep loudly and repeatedly when a vehicle moves in reverse.

When this detector senses high levels of combustible and toxic gases, it alerts you with an audible alarm, warning light, and vibrating alarm.

Measure and display real-time indoor ventilation quality.

When these detectors sense high levels of carbon monoxide, they alert you with an audible alarm, warning light, and vibrating alarm.

These detectors trigger a “caution” alert when a small amount of hydrogen is detected and a second “danger” alert if levels continue to rise.

An audible alarm and warning light alert you to the presence of methane.

When these detectors sense high levels of hydrogen sulfide, they alert you with an audible alarm, warning light, and vibrating alarm.

Measure temperature, humidity, and radiant heat in your work area to keep your team safe from heat-related hazards.

Check temperature, relative humidity, atmospheric pressure, and time with one barometer.

Connect switches, transmitters, actuators, and other equipment to your PLC for complex automation jobs.

Prevent damage to electronic equipment caused by spikes in current. Mount these receptacles to DIN rail.

Prevent damage to electronic equipment caused by spikes in voltage.

Detect lower levels of radiation than our standard detector. Measurements are displayed on an easy-to-read LCD.

Check for leaks in pipes, valves, storage tanks, and other gas system components.

Easy-to-see colors enable you to visually inspect for leaks in hydraulic systems without ultraviolet lights.

When a tiny amount of liquid makes contact with the pH patch, it changes color to indicate a leak.

Monitor the health of pumps, engines, and other rotating equipment from your wireless device.

Two easy-to-set dials allow you to adjust a set activation point for vibration as well as a time delay to avoid false triggering from start-up vibration. An LED alarm signals if the set activation point is exceeded.

Keep machinery running smoothly by monitoring its health and status from your computer. Often used with electric motors, pumps, and lathes, these kits measure changes in vibration, and temperature—identifying equipment problems and potential failures before they occur.

Provide a signal you can see and hear. Choose from a bell, horn, or chime tone.