Slot these counters into a control or electrical panel cutout.

These counters have mounting holes and a base plate for securing to a wall or work surface.

Slot these counters into a control or electrical panel cutout.

Connect the lever on these counters to an object moving repetitively in a straight line, such as a punch or drill press.

Precisely count rotations by attaching these counters to clutches, couplings, rotors, or other rotating shafts.

These meters do not require voltage to register a count.

Slot these counters into a control or electrical panel cutout.

Send a signal to another device when the counter reaches a set point. The signal can start/stop a process or trigger an alarm.

Wire these counters/ratemeters to an electrical pulse-emitting switch, sensor, or encoder to count input while tracking rates in units such as gallons per minute.

Keep your phone in your pocket and your hands free—these smartwatches perform a variety of functions on your wrist.

Quickly view starts and finishes on a digital screen.

Combine a counter, feeder reel, coiler reel, and stand to create a wire, cable, and cord length measurer.

Feed wire through the wheels inside the included counter to take measurements.

Record steps or miles while you walk or run.

Install this totalizer on your grease gun or valve to measure grease dispensing and reduce waste.

Often used in hard-to-access areas, these totalizers let you monitor the total amount of drinking water flowing through them up to 250 feet away.

Meeting NSF/ANSI 61, these totalizers measure the cumulative amount of drinking water flowing through them.

The digital display on these totalizers makes it easy to check the total amount of high-temperature liquid—up to 200° F—passing through your system.

Measure the total amount of liquid flowing through these totalizers.

Determine the amount of gasoline, diesel fuel, and kerosene that flows through these totalizers.

Often used in low-flow metering applications for lubricants or antifreeze, these transmitters measure flow rate and send the data to a remote display or programmable logic controller (PLC).

Send flow rate data using these transmitters while also being able to visually confirm liquid is flowing.

Send flow rate and temperature measurements simultaneously to a programmable logic controller (PLC), data logger, or other receiving device.

Install these transmitters between two flanges in a flanged pipe system to measure flow rate and send the data to a remote display or programmable logic controller (PLC). For easy cleaning and maintenance, you can slide the transmitter out from between the flanges.

Commonly referred to as thermal mass flowmeters, these transmitters calculate flow rate by measuring how much they cool as air and other gases pass through them. This means they’re accurate even if there are temperature and pressure changes, unlike most other transmitters.

Use these flowmeter/totalizers to measure both the flow rate and total flow volume of oil, gasoline, diesel fuel, and kerosene.

With one meter, these flowmeter/totalizers measure the flow rate and total flow volume of high-temperature liquid up to 200° F.

The unthreaded ends of these flowmeter/totalizers install into a PVC piping system, so you can measure the flow rate and volume of liquid passing through your system.

Made with metal and chemical additives, these calculators trigger metal detectors and X-rays if they fall into your food line, helping you comply with Hazard Analysis and Critical Control Point (HACCP) programs for food safety.

More precise than test strips, this meter is often used to measure the pH of dirty liquids in agricultural systems, aquaculture tanks, and printing fountains.

Check pH in harsh field conditions. These floating meters that have a housing that meets IP67 for complete resistance to dust and protection from temporary submersion.

Measure a solution’s oxidation reduction potential (ORP) to determine its ability to break down contaminants.

Pour contaminated water, wastewater, printing fountain solutions, and other dirty liquids into the meter cup to test electrical conductivity levels that indicate the concentration of salts, nutrients, chemicals, and other substances.

Don’t worry about dropping this meter in your tank when checking electrical conductivity—it floats and has a housing that meets IP67 for complete resistance to dust and protection from temporary submersion.

Test different water-chemistry measurements in dirty, wet conditions.

Check the pH and conductivity of water and other clean liquids with one bench-top device.

In addition to a transmitter, these kits include a 6 1/2-ft. cable and a mounting bracket.

Also known as encoders, these sanitary transmitters convey motion to an electrical signal that conveys distance, direction, and speed. They’re often used in control systems to automate servomotors, robotics, and assembly machines in sanitary environments such as food and pharmaceutical plants.

Slide one of these transmitters onto a motor shaft in your application—they have a flexible mounting plate that compensates for shaft misalignment and vibration.

These scoreboards automatically count days.