For a long-lasting cutting edge that's three times harder than uncoated stainless steel, the blades on these scissors are titanium bonded over stainless steel.

Minimize hand fatigue with a lightweight handle and spring-action that automatically opens the blades for quick repeat cuts.

Longer handles and shorter blades give you more leverage than other scissors to cut tough materials such as leather, rope, and thick cardboard.

Minimize hand fatigue—the handles on these scissors are lightweight and spring-action opens the blades for quick repeat cuts.

For extra leverage to cut through tough materials such as leather, rope, and thick cardboard, these scissors have long handles and short blades.

Prevent snags and injury with the rounded points on these small scissors.

For extra leverage to cut through Kevlar, metal, and plastics, these scissors have long handles and short blades.

With high-carbon stainless steel blades, these scissors cut through fiber-optic and electrical cables, even those that are made with Kevlar. They’re also good for cutting wire jackets and cable ties.

Also known as electricians' shears, the back edge of the blade has a file to clean contacts.

These cutters make straight cuts and curves.

Blades are tapered to give you more control when cutting straight lines, tight curves, and circles, and they're serrated to prevent slipping. These cutters are also known as duckbill snips.

Made from aluminum bronze, the blade and handle on these cutters inhibit sparking and are FM approved. Use them for straight cuts.

Handles are angled to keep your hand away from the material as you cut straight lines and curves.

Keep your hand away from the material being cut.

The handles are angled 90° from the blade so you can cut material from directly above tight spaces.

Prevent waste from flying up as you work. A double blade makes two cuts to create a 7/64"-wide step that peels back, leaving little distortion and smooth edges.

A double blade creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.

Punch small pieces out of material to create an almost burr-free cut with no material distortion.

Also known as slotting shears, these cutters have a double blade that creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.

Also known a scissor-blade shears, the bottom blade remains stationary while the upper blade moves up and down to cut metal up to 1/64" thick with minimal material loss and edge distortion.

Make straight, clean cuts in thick sheet metal.

This large-capacity cutter has a 25" blade for long, straight cuts.

Combine the cutting base and a corner punch to make rounded corners in sheet metal.

Good for high-volume cutting and trimming.

Cut straight lines and patterns with the rotary blades on this cutter.

A double hinge provides high cutting force with low gripping pressure.

Sharpen or replace the jaws as they wear. These cutters have a double hinge that provides high cutting force with low gripping pressure.

Cut hard steel wire, nails, and small rivets close to the surface with the wide, flat jaws on these cutters.

Made of beryllium copper that is FM approved, these cutters satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

These powerful cutters make diagonal cuts with a nipping action to cut extra-hard wire with ease.

Handle is angled 30° to keep work in sight and hands clear of the work surface. Blades are flat on one side for close-to-the-surface cuts.

With a short-nosed jaw, these cutters force the material being cut deeper into the jaw for maximum leverage. The short jaw also allows you to cut one side of a chain link or padlock hasp without hitting the other side.

Insulated handles protect against shock from accidental contact with live electrical circuits. These cutters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Slice through bolts and chain with low effort.

Minimize material distortion while cutting steel and stainless steel wire rope.

Keep your hands in a comfortable position so you can apply more force for cutting.

A small grip enables one-handed cutting.

Use the lever to make one-handed cuts with minimal material distortion. Cutter mounts to a workbench for extra stability and ease of use for repeated cuts.

Make clean cuts on threaded rod with the pull of a trigger.

Leverage points in both the jaws and the handle give you more power with less effort.

Also known as diagonal-cutting pliers.

These cutters are stainless steel, which provides excellent corrosion resistance.

These sets include four cutters, each with a different head shape.

The specially designed internal spring provides constant, uniform tension for superior performance.

Produce clean, distortion-free cuts in cable with one-handed operation.

Use these one-handed cutters on small-diameter aluminum and copper power and communication cable.

Insulated handles protect against shock from accidental contact with live electrical circuits. These cutters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.